Stonecare PRO Signature Stone Polishing Powder (aka Majestic 5X) is an excellent performer to polish to a deep gloss all calcite-based stones, such as Marble, Travertine, Onyx, Limestone, etc.
A balanced blend of selected powders to polish all calcite-based stones. It is the original, world-famous Italian “5 Extra” (a.k.a. Majestic “5 X”) It was formulated to be used for “wet-polishing.”
For Professional Use Only.
Stonecare PRO Signature MARBLE, TRAVERTINE, LIMESTONE POLISHING POWDER
A balanced blend of selected powders to polish all Calcite-based stones! It is the original, world-famous Italian “5 Extra” (a.k.a. Majestic “5 X”). It was formulated to be used for “wet-polishing.”
For Professional Use Only
DIRECTIONS: The following are AVERAGE directions. Different stones may require different techniques. In doubt, don’t hesitate to contact us.
-
Prepare the surface to be polished by honing it to the highest clarity possible.
-
Protect surfaces that could be damaged by splatters with proper masking material.
-
FLOORS: Target an area of approximately 10 – 12 sq. ft. and sprinkle approximately 4 tablespoons of Majestic 5X on the middle of it, possibly in a circular pattern slightly narrower than the diameter of the floor machine. Position a “hog-hair” pad (highly recommended) on top of the powder and the floor machine with the water tank full of water on top of it. The machine cannot exceed 175 RPM for best results and needs at least 1.5 HP. Release some water and swiftly swing the machine back and forth over the targeted area (to evenly spread the slurry), then polish slowly with a spiral motion moving from one end of the targeted area to the other and back. Release some more water and repeat. Release plenty of water and go over the polished area swiftly. Suck up the slurry with a wet-and-dry vacuum cleaner. Check the results. If they are not satisfactory, repeat with more or less powder, depending on the obtained result.
-
TOPS: Target an area of approximately 2 or 3 sq. ft. Sprinkle a little 5X on the surface to be polished in a circular pattern to be narrower than the polishing pad to be used. Spray some water on the powder and over the rest of the targeted area. Set the speed of the right-angle grinder/polisher (variable speed is a MUST) at 600 RPM. Position a white or red nylon pad (3M brand is better). Controlling the speed with the trigger and applying as much pressure as the machine can take, start spreading the slurry over the targeted area keeping a very low RPM, until it’s almost dry. Pull the trigger all the way while gradually lightening the pressure and buff for several seconds before checking with a squeegee. Repeat if necessary adjusting the quantity of powder and/or water accordingly.
COVERAGE: Depending on the type of stone, expect coverage of approximately 250 to 500 sq. ft. per pound.
FOR PROFESSIONAL USE ONLY
CAUTIONS: This product is corrosive (acidic). Some individuals may be sensitive to its contact.
SAFETY TIPS: Wear gloves, goggles and protective clothing. Keep small children and pets out of the area where the product is been used. Store only in its original container. KEEP OUT OF REACH OF CHILDREN.
EMERGENCY FIRST AID PROCEDURES.
IF SWALLOWED: Do NOT induce vomiting. Drink large quantities of water. Seek medical attention if symptoms develop. EYE AND SKIN CONTACT: Flush with plenty of water. If irritation persists, seek medical attention. INHALATION: Relocate to fresh air. If symptoms develop, seek medical attention.
GUARANTEE OF SATISFACTION: ALWAYS TEST BEFORE USING! If not satisfied with the performance of this product when used according to directions, Stonecare Central will refund the purchase price – or replace the product at its sole discretion – upon production of valid proof of purchase. THE RESPONSIBILITY OF Stonecare Central IS LIMITED TO THE PURCHASE PRICE OF THIS PRODUCT. No warranties, expressed or implied, extend beyond the description on this label.
